We've seen a Linux-based operating system made to run on some widely varying pieces of hardware over the years, but [Dimity Grinberg]'s latest project may be one of the most unusual. It's a PCB with 3 integrated circuits on it which doesn't seem too interesting at first, but what makes it special is that all three of those chips are in 8-pin SOIC packages. How on earth can Linux run on 8-pin devices? The answer lies as you might expect, in emulation.

Two of the chips are easy to spot, a USB-to-serial chip and an SPI RAM chip. The processor is an STM32G0 series device, which packs a pretty fast ARM Cortex M0+ core. This runs a MIPS emulator that we've seen on a previous project, which is ripe for overclocking. At a 148 MHz clock it's equivalent to a MIPS running at about 1.4 MHz, which is just about usable. Given that the OS in question is a full-featured Debian, it's not running some special take on Linux for speed, either.

We like some of the hardware hacks needed to get serial, memory, and SD card, onto so few pins. The SD and serial share the same pins, with a filter in place to remove the high-frequency SPI traffic from the low-frequency serial traffic. We're not entirely sure what use this machine could be put to, but it remains an impressive piece of work.

From Blog – Hackaday via this RSS feed

If you flew or drove anything remote controlled until the last few years, chances are very good that you’d be using some faceless corporation’s equipment and radio protocols. But recently, open-source options have taken over the market, at least among the enthusiast core who are into squeezing every last bit of performance out of their gear. So why not take it one step further and roll your own complete system?

Apparently, that’s what [Malcolm Messiter] was thinking when, during the COVID lockdowns, he started his own RC project that he’s calling LockDownRadioControl. The result covers the entire stack, from the protocol to the transmitter and receiver hardware, even to the software that runs it all. The 3D-printed remote sports a Teensy 4.1 and off-the-shelf radio modules on the inside, and premium FrSky hardware on the outside. He’s even got an extensive folder of sound effects that the controller can play to alert you. It’s very complete. Heck, the transmitter even has a game of Pong implemented so that you can keep yourself amused when it’s too rainy to go flying.

Of course, as we alluded to in the beginning, there is a healthy commercial infrastructure and community around other open-source RC projects, namely ExpressLRS and OpenTX, and you can buy gear that runs those software straight out of the box, but it never hurts to have alternatives. And nothing is easier to customize and start hacking on than something you built yourself, so maybe [Malcolm]’s full-stack RC solution is right for you? Either way, it’s certainly impressive for a lockdown project, and evidence of time well spent.

Thanks [Malcolm] for sending that one in!

Posted from Blog – Hackaday RSS Feed: https://hackaday.com/blog/feed/ About / feedback: !meta@rss.ponder.cat

We remember when the transputer first appeared. Everyone "knew" that it was going to take over everything. Of course, it didn't. But [Oscar Toledo G.] gives us a taste of what life could have been like with a JavaScript emulator for the transputer, you can try in your browser.

If you don't recall, the transputer was a groundbreaking CPU architecture made for parallel processing. Instead of giant, powerful CPUs, the transputer had many simple CPUs and a way to chain them all together. Sounds great, but didn't quite make it. However, you can see the transputer's influence on CPUs even today.

Made to work with occam, the transputer was built from the ground up for concurrent programming. Context switching was cheap, along with simple message passing and hardware scheduling.

The ersatz computer has a lot of messages in Spanish, but you can probably muddle through if you don't hablar español. We did get the ray tracing example to work, but it was fairly slow.

Want to know more about the CPU? We got you. Of course, these days, you can emulate a transputer with nearly anything and probably outperform the original. What we really want to see is a GPU emulation.

Posted from Blog – Hackaday RSS feed, see !meta@rss.ponder.cat

[Morten] works very fast. He has already designed, fabbed, populated, and tested a breakout board for the new tiniest microcontroller on the market, and he’s even made a video about it, embedded below.

You might have heard about this new TI ARM Cortex MO micro on these very pages, where we asked you what you’d do with this grain-of-rice-sized chunk of thinking sand. (The number one answer was “sneeze and lose it in the carpet”.)

From the video, it looks like [Morten] would design a breakout board using Kicad 8, populate it, get it blinking, and then use its I2C lines to make a simple digital thermometer demo. In the video, he shows how he worked with the part, from making a custom footprint to spending quite a while nudging it into place before soldering it carefully down.

But he nailed it on the first try, and honestly it doesn’t look nearly as intimidating as we’d feared, mostly because of the two-row layout of the balls. It actually looks easy enough to fan out. Because you can’t inspect the soldering work underneath the chip, he broke out all of the lines to a header to make it quick to check for shorts between those tiny little balls. Smart.

We love to see people trying out the newest hotness. Let us know down in the comments what new parts you’re trying out.

Thanks [Clint] for the tip!

Posted from Blog – Hackaday RSS feed, see !meta@rss.ponder.cat

If you’re on the US East Coast, you should head on over to Wall, NJ and check out the Vintage Computer Festival East. After all, [Brian Kernighan] is going to be there. Yes, that [Brian Kernighan].

Events are actually well underway, and you’ve already missed the first few TRS-80 Color Computer programming workshops, but rest assured that they’re going on all weekend. If you’re from the other side of the retrocomputing fence, namely the C64 side, you’ve also got a lot to look forward to, because the theme this year is “The Sounds of Retro” which means that your favorite chiptune chips will be getting a workout.

[Tom Nardi] went to VCF East last year, so if you’re on the fence, just have a look at his writeup and you’ll probably hop in your car, or like us, wish you could. If when you do end up going, let us know how it was in the comments!

Posted from Blog – Hackaday RSS feed, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed via bot, see !meta@rss.ponder.cat

Posted from this RSS feed by RSSBot, see !meta@rss.ponder.cat

Posted from this RSS feed by RSSBot, see !meta@rss.ponder.cat

Posted from this RSS feed by RSSBot, see !meta@rss.ponder.cat

Posted from this RSS feed