66
Wood Temp Tower (lemmy.world)
submitted 3 months ago* (last edited 3 months ago) by MissJinx@lemmy.world to c/3dprinting@lemmy.world
21 comments fedilink hide all child comments

This is the temp tower of my wood print experiment Cand even se much difference. It goes from 260 to 190. Below 225 gets really flimsy and above 240 melts. But even 230, the "best" one is really bad, and I'm not talking about retraction. Even the layers that melt are inconsistent.

Also it's not humidity since the filament was in a filament dryer for.16hours.

edit: The nozzle is 0.8

can someone think of anything else?

top 21 comments
sorted by: hot top controversial new old
[-] NaibofTabr@infosec.pub 17 points 3 months ago

Did you change the nozzle setting in your slicer to 0.8? They usually default to 0.4

It definitely looks under extruded.

[-] ThePantser@lemmy.world 14 points 3 months ago* (last edited 3 months ago)

Looks like a partial clog and too fast at the same time. A .8 nozzle lets a lot of material flow, try slowing down after checking for a clog.

Oh and are you skipping steps?

[-] AnarchoSnowPlow@midwest.social 9 points 3 months ago

Yeah that immediately looks way under-extruded to me.

Also that wood stuff (from what I read) clogs terribly.

[-] MissJinx@lemmy.world 5 points 3 months ago

Yes that's why I'm using a .8 nozzle lol

[-] FuglyDuck@lemmy.world 2 points 3 months ago

can you print PLA on the .8 nozzle just fine? (I'd suggest clearing the clog- an atomic pull is my go to, maybe followed up with some cleaner filament, then a filament you know well.)

for some comparison, a .8mm nozzle has about four times the crosssection of a .4mm nozzle. (.502 to .125 mm^2), similarly, the volume of a 1mm line printed, assuming you're using a line width equal to the nozzle and a half your nozzle diameter in layer height, is about 4 times as much, as well. ( .32 mm^3 compared to .08 mm^3.)

in short, given the same printing speed, and the same diameter filament, you're going to have to extrude 4 times as much filament at any given moment, which means the filament will have to pushed through much faster than a .4mm nozzle, which in turn means that the plastic has about a quarter of the time to heat up before being pushed out of the nozzle tip- and there's more of it to absorb the heat.

There's a few things you can try, but probably the only one that would be effective without more or less rebuilding the hotend (and the new-parts-cost associated with that,) is slowing it down.

For the record, if it wasn't clogged before, it probably is now. since, ultimately, what would be happening is that the .8mm nozzle is causing your printer to print cold.

[-] MissJinx@lemmy.world 2 points 3 months ago

tbf my printer don't print well not even in 0.4. The 0.8 is printing better than the 0.4 was. I think the hot end may be the real problem indees

[-] MissJinx@lemmy.world 1 points 3 months ago

Can be a clog. I read that wood should be faster so.it wouldn't clog, but it could be this too . I'll try slowing down and checking the nozzle! thanks for the idea!

[-] roofuskit@lemmy.world 1 points 3 months ago

You can't both push a bunch of extra material and print faster. Hotends have volumetric limits.

[-] KeraKali@lemmy.world 12 points 3 months ago

Are you sure the gcode actually makes the printer change temps? Good thing to double check since it looks the same throughout

[-] Linktank@lemmy.today 6 points 3 months ago

If you focus only on the little pylon within the circle you can see a clear trend.

[-] MissJinx@lemmy.world 5 points 3 months ago

hum ill check but I used orca native temp tower and chrcked through the print? it didi chsnge. could it be a hardware problem?

[-] papalonian@lemmy.world 6 points 2 months ago

This is how my wood PLA+ prints used to look too. Your extruder is almost 100% the issue. These filaments are spongy and don't extrude well. Try toying with your extruder tension and if that fails get a BMG knockoff

[-] MissJinx@lemmy.world 1 points 2 months ago

I thought so! My extruder was never good. Thanks I'll look at a bmg

[-] Grass@sh.itjust.works 6 points 3 months ago

I don't know what your setup is but that looks to me like you need a higher flow melt zone and better extruder grip. I was able to get out of a similar situation with particle filled filaments using this: https://kevinakasam.com/papilio/ and further improvement with a hall effect filament width sensor but the tinkering for that was an actual nightmare.

wood filament is also just cursed. the improvement to regular filament was much better while the particle filaments just went from similr to your wood filament to tolerable.

[-] MissJinx@lemmy.world 1 points 3 months ago

oh that's interesting my extruder is indeed kind of shitty. I'll take a look at this thanks

[-] TechAdmin@lemmy.world 2 points 2 months ago

What are max print speed and volumetric set to?

For some filaments (silk PLA) I've had to slow things down (120mm/s max print speed and 10mm3/s max volumetric speed) or it comes out horrible. Only used 0.4 nozzles so far though.

[-] MissJinx@lemmy.world 1 points 2 months ago

my print speed is at 60mm

[-] takingbacksunday@lemmy.world 2 points 3 months ago

I am definitely thinking you have a partial clog. Get that sorted out first, then run flow rate tests as well

[-] MrIamsosmrt@feddit.org 1 points 2 months ago

Have you tried adjusting the e steps?

[-] FuglyDuck@lemmy.world 0 points 3 months ago

Looks to me like the plastic isn’t getting hot enough fast enough.

Is it just wood filament that isn’t printing right? Can you print pla or whatever on the .8mm?

Does the filament brand suggest a range that’s higher than you normally print at?

[-] MissJinx@lemmy.world 1 points 3 months ago

No, crealty wood. If its too hot it burns

this post was submitted on 30 Aug 2024
66 points (100.0% liked)

3DPrinting

15658 readers
125 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 2 years ago
MODERATORS
andypiper@lemmy.world
henry_rowengartner@lemmy.world
j4k3@lemmy.world
GrayBackgroundMusic@lemm.ee