My ds4 works out of the box— the touchpad even maps to the mouse cursor (I use libinput and Wayland).

Ds4drv, if you use it, will override the default kernel driver I believe. Make sure it’s not emulating an Xbox 360 controller, unless you want that.

ArchWiki also mentions that you need to disable hidraw in Wine. Maybe that’s related, if you have issues with Windows games?

If you’re feeling adventurous, you could compile Marlin yourself. I did it to use a pin as an “off” signal for my fans, but ended up tinkering with options like linear advance. The set up isn’t too hard, but you need vscode.

Her name is Link 😒

Which VCS do you use?

The First AAAA game

BeReal was cool, and the concept is still appealing to me and my circle.

The groups and the celebrity/brand accounts aren’t cool. And I can imagine them adding more garbage after this acquisition.

At the end of the day, capitalism gonna capitalize~

Gonna give this a try! I’ve been jumping between clients on my Hyprland desktop… rn I can’t do global PTT on any third-party apps, despite Hyprland passing the input through to the app exclusively. I haven’t even looked at Vesktop, though!

I should buy it, I loved control and I love the recent resident evil games

Here’s my results:

From top to bottom in pictures:

• 45 degrees with organic supports on entire bottom shaft (not in second image)
• Horizontal with organic supports on entire bottom shaft
• Vertical with organic supports on bottom end bit and a few spots on the shaft near the bottom

Here’s my thoughts on them:

The 45 degree one was really poor quality on the bottom… and the back part snapped when I was trying to remove supports. It likely would’ve been a bit stronger printing with taller layers, but the bottom edge seems tricky to support regardless.

The horizontal one turned out well. The bottom side has a rough finish from where the supports connected, but I think being more picky about painting on supports and giving that side a quick shave after printing would fix. The tip is still pretty smooth, to my surprise! Also, this printed twice as quick as the vertical one, since I didn’t have to slow any movements. I can’t break this one even if I try— it’s super strong, the bridge included. Just bends. That said, the nub on this one is more of a nub than a bump, a bit sharper. Between that and the surface on the bottom, it doesn’t fit in my 3ds without doing any shaving or sanding. However, the “tail” part, which shows in the 3ds, is smoothest off-the-bed in this orientation.

Lastly, I printed another vertical one because I wanted to figure out why the bridge at the bottom wasn’t complete in the sliced model:

My solution was reducing the “minimum perimeter width” for the Arachne generator down to 50% (of the nozzle diameter) from 85%. Anyways, this print has a smoother, shinier finish along the shaft and tip. On this print, the nub near the bottom is more of a gradual bump compared to the horizontal one. With this print, though, as the height increases, you can see a bit of wobble and there is a Z-seam running up the shaft. Also, I don’t trust bending this stylus very much, especially the bridge part, since that’s what broke first last time. Seems sturdier this time with the perimeter change, but only a bit. And finally, the “tail” is the roughest here, since it’s the part that was connected to the raft. It’s probably worth sanding it down to get a good finish there.

Here’s the model if you’d like to print one for yourself: https://www.printables.com/model/158481-new-nintendo-3ds-stylus

Anyways, I’ve learned a lot in this process. And now I can play Ace Attorney with a stylus again!!

Definitely would’ve been easier to print (less tinkering with slicer settings), too. But I think because the layer time was so quick, it’s surprisingly well-bonded.

That’s still the first direction it’s snap in, but I think it’s good enough for my use-case.

It definitely does seem sketch, but the creator of the model recommended printing it vertically— it makes the gap, nub and tip a bit smoother.

I had to slow the layers a bit and play with the raft and supports (I originally did a 3ds xl stylus a few months ago, that’s where my trial-and-error was)

Here’s how it turned out: https://lemmy.ca/comment/8779564