Setting up my server as a newbie some years ago, I did not have the ability to purchase more then one 8TB hard drive. Outgrew that rather quick and now I have two additional 16TB drives, in a Just A Bunch Of Disk configuration, mounted to different /mnt mount points. I know this is not ideal, but lacking the ability to expand further or buy new drives for a new zfs pool and transfer, I don't have much of a choice but to wipe the drives, set up a zfs raid and re-download everything.

I have everything set up in docker-compose files, so I'm pretty sure I just need to keep those and the folders where the configs are, modify the compose files with the new file structure and... I am unsure where to go from here. Will everything start being grabbed as soon as my dockers spin up? Is there an additional procedure I need to do to make sure I don't wipe my existing config files with blank empty ones? Is there an easier way of doing this?

I have an 8gb Raspberry Pi 4 that has been a workhorse for years. I keep it for my not intense but essential networking purposes, NetBoot.xyz, Homepage, etc., because I can run it over PoE (edit: Power over Ethernet), so it is always on as long as my network is up.

It is growing long in the tooth, and I find myself wanting to replace it with something a bit more capable. Looking at the 8gb Pi 5 at $80 plus another $30 for a PoE hat, I wonder if there is something out there that would be a better value for running PoE? Can you convert a micro pc over to PoE? Does anyone have any recommendations for computers that run off PoE or can be converted to PoE?

I am trying to set up a repository of knowledge for my job. Was thinking a wiki, but I need something that I can make as simple as possible for the end user, as some of them are not familiar with markdown or html. Is there a self hosted option that is dumb easy simple to navigate and edit for the end user?

I have friends and relatives that would like to do some memory and compute intensive tasks, but lack the hardware locally. I have loads of ram doing nothing and a little compute to spare. Is there a way for me to set up some service accessible to them that would allow them to spin up VMs, similar to Linode or DigitalOcean? I know letting outside access to a proxmox server would be disastrous. I guess I could setup a VPN server into a virtualized proxmox server? Would rather find a way to point them to a url with a username and password and have them able to use my server as their vps like AWS or Linode.

Got this sickly looking peach tree in the end of May. After about a month I started seeing red/black spots on the leaves and it looked like something what eating them. Did some research and started spraying it with neem oil. The spots stopped happening on newer hight leaves, as well as the bite marks. Now all the leaves are falling off and it looks like this. Is it dead? Does it have any hope? What can I do to put it on life support and make it through the winter?

first off, thanks for everyone and their suggestions, and apologies for not responding back, was having issues with my personal lemmy instance.

I took everyone's advice and have gone test print crazy. I will attach the pictures to this post. I have tried to understand what I am looking at on my test prints in relation to what is not configured correctly on my printer. it's just not clicking. most of my prints look fine, the surface has good infill and the part looks ok from the outside, like benchie. but underneath, it looks like I am having either adhesion issues, bridging problems and support problems as well. but adjusting setting as suggested in here and here did not really improve anything, and in some cases made the print worse.

I am using the Flashprint slicer that came with the printer. I have tried cura and prusaslice and can't even get a print started on those, even with a raft. I'm sure they are better slicers that what Flashforge makes, but again, something just isn't clicking. any further advice would be greatly appreciated.

I am trying to finally get my homelab organized, and I need assistance visualizing my network. I am just wondering if there are tools out there that assist with this. I have tried the paint and gimp routes, and I find myself spending more time trying to make it look good and organized rather than actually mapping my network. Is there any utility out there that is purpose build just for visualizing network topology? Or am I better off with just graph paper, pencil and a straight edge?

Just picked up an APC 48u server rack. There were no pictures of it in the post and I did not notice until I got it home and set up, that the rack rails have threaded holes instead of square cage nut holes. I can’t seem to determine the thread size and pitch, and have a thread gauge coming. Until then, does anyone know anything about this? The people I grabbed it from had used self tapping machine screws and drove them in with an impact wrench. Is this what APC had intended, or is there some $300 proprietary screw I have to buy from them?

Running proxmox 8.0.3, spinning up new VM, noticed my netboot was SSLLOOWW. ran speedtest-cli in the host shell, was getting 4Mbits/s, ran on a VM on that same system, was getting 500-600 Mbits/s. I have NO clue what to make of this. Is this a bridge issue in proxmox? I don't think it's a DNS issue, everything else is working, business as usual, even still serving plex and arr on the same system. Any ideas to get me running in the right direction?

Edit: It's DNS. It's always DNS. Disabled AdGuard Home and magically speeds on the host were back. Confused, but have a direction at least.

I wanted to thank everyone that responded to my last post. Everyone gave good advice, and hearing that everyone hit a wall they had to just grind through helped a lot.

Took my sorceress and mixed things up. Didn’t focus on one element, and tried to match attributes in the skill tree instead of elements. Still have hydra as my main focus, but I rely very heavily on chain lighting and frost nova. I was actually able to finish act II.

Again, thank you all for the awesome words. You guys a super swell!

Diablo was the first game I ever bought for my perfoma Mac when I was a kid. I have played out each game since. I played the betas. I have reached a point where I do not know what to do.

I have not finished the campaign. In fact I haven’t even finished act III. Both my barbarian and sorceress have appeared to have reached a plateau at around level 35.

At around level 30, in world tier II, I started getting really terrible drops. Magic only, legendary that was worse that what I had. Finally around 35 for my sorceress and 37 with my barb, I got fed up with the terrible drops and just took the first positive change I found and went back out to see if this would yield better loot.

The first bear I meet I use all my health potions on. My attacks seem to take less health away. I finally make it to a dungeon. Can’t make it to the boss because I keep dying.

I figured I sold my sweet gear, let me just jump back to world tier I and grind till better loot falls. Bears still three hit me, and I still get crap loot.

I changed my skill load outs, made best use of the loot I got and continued to try and grind to get better loot. I still only got magic and crap legendary.

What am I supposed to do at this point? I can’t make it to a dungeon to fight a dungeon boss without having to TP back to replenish my potions a half dozen times. Can’t move the campaign forward, simple crowd of minions melt me in a second. Monsters don’t even drop health globes. Am I just supposed to start a new character and hope I don’t repeat this same mistake again? How are you supposed to recover from a mistake like that?