I have a Dell Latitude 5420 laptop with LMDE, running kernel 6.1.0-12. This laptop has a builtin I219-LM ethernet controller that I can see via lspci. Some research indicates that this needs the e1000e kernel module, so I grabbed it from Intel, compiled it, and installed it. There were some complaints during the compilation, but nothing more than the average compilation process. Plus, it shows up in lsmod. Afterwards, lspci -vv displays it with the e1000e driver:

0000:00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (13) I219-LM (rev 20)
        Subsystem: Dell Ethernet Connection (13) I219-LM
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 16
        IOMMU group: 15
        Region 0: Memory at a6100000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [c8] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Kernel modules: e1000e

However, when I do lshw, it is listed as unclaimed:

  *-network:1 UNCLAIMED  
       description: Ethernet controller  
       product: Ethernet Connection (13) I219-LM  
       vendor: Intel Corporation  
       physical id: 1f.6  
       bus info: pci@0000:00:1f.6  
       version: 20  
       width: 32 bits  
       clock: 33MHz  
       capabilities: pm msi cap_list  
       configuration: latency=0  
       resources: memory:a6100000-a611ffff  

...and of course, it's still not showing in ifconfig. So, where do I go from here? Did I miss anything obvious?

And just for the record, I know that the ethernet port is working. It worked fine in Win11 before wiped the PC completely.

Does anyone know how I can select my audio output via the command line? I'm frequently switching between using my monitors inbuilt speakers and a USB audio interface and I'm finding it laborious to navigiggerate graphically through the settings in GNOME to do so.

What I'd like to do is set up a couple of bash aliases and do it in my terminal.

What's the best way for me to do that?

Many thanks

Apparently I installed that thing in 2006 and I last updated it in 2016, then I quit updating it for some reason that I totally forgot. Probably laziness...

It's been running for quite some time and we kind of forgot about it in the closet, until the SSH tunnel we use to get our mail outside our home stopped working because modern openssh clients refuse to use the antiquated key cipher I setup client machines with way back when any longer.

I just generated new keys with a more modern cipher that it understands (ecdsa-sha2-nistp256) and left it running. Because why not 🙂

Ubuntu Core Desktop is an immutable distro, takes a different path than most other immutable distros.

• The entire OS is built using snaps, including the kernel and bootloader
• Uses snaps instead of flatpak
• Prefers LXD over distrobox and other projects that use podman

My laptop isn't under my supervision most of the time. And I'd hate it if someone were to steal my SSD, or whole laptop even, when I'm not around. Is there a way to encrypt everything, but still keep the device in sleep, and unclock it without much delay. It's a very slow laptop. So decryption on login isn't viable, takes too long. While booting up also takes forever, so it needs to be in a "safe" state when simply logged out. Maybe a way that's decrypt-on-demand?

I'm on Arch with KDE.

Notable changes

• Add experimental color management protocol support
• Use libadwaita for server-side decorations on GNOME (on Xorg and Xwayland apps)
• Let scaling-aware Xwayland clients scale themselves
• Add initial PipeWire explicit sync support

Beside DE and terminal commands , is there anything else I should try in a linux distro ?

I’ve been using Arch for just over a year on my older Dell laptop, and have been regularly running sudo pacman -Syu but not once have I had a problem or anything break. What am I doing wrong?

So, I have a Steelseries M800 keyboard and a Corsair mouse. Unfortunately neither of them are supported by Open RGB, and so I'm stuck with my RGB making rainbows.

Well, sort of. My keyboard still has the configuration it had from when I still used Windows over 2 years ago. But my mouse does not.

I use an XP Pen tablet for making art, and the official driver from XP Pen doesn't come with any options to adjust and calibrate the screen's colours, but I managed to figure out how to access these hardware settings through command line. Now this has me wondering if it's possible to do the same for my keyboard and mouse.

I like my Linux installs heavily customized and security hardened, to the extent that copying over /home won't cut it, but not so much that it breaks when updating Debian. Whenever someone mentions reinstalling Linux, I am instinctively nervous thinking about the work it would take for me to get from a vanilla install to my current configuration.

It started a couple of years ago, when dreading the work of configuring Debian to my taste on a new laptop, I decided to instead just shrink my existing install to match the new laptop's drive and dd it over. I later made a VM from my install, stripped out personal files and obvious junk, and condensed it to a 30 GB raw disk image, which I then deployed on the rest of my machines.

That was still a bit too janky, so once my configuration and installed packages stabilized, I bit the bullet, spun up a new VM, and painstakingly replicated my configuration from a fresh copy of Debian. I finished with a 24 GB raw disk image, which I can now deploy as a "fresh" yet pre-configured install, whether to prepare new machines, make new VMs, fix broken installs, or just because I want to.

All that needs to be done after dd'ing the image to a new disk is:

• Some machines: boot grubx64.efi/shimx64.efi from Ventoy and "bless" the new install with grub-install and update-grub
• Reencrypt LUKS root partition with new password
• Configure user and GRUB passwords
• Set hostname
• Install updates and drivers as needed
• Configure for high DPI if needed

I'm interested to hear if any of you have a similar workflow or any feedback on mine.

cross-posted from: https://lemy.lol/post/30548063

I have an old hp pavilion dv6 and I installed windows 7. Then i tried installing Ubuntu 24.04 and the USB wouldn't boot, it just showed "GRUB" in the top left of the screen. I tried with another USB and the same issue emerged.

Hi everyone i have some issue with my gpu vbios(i bought an used gpu with custom bios than dont support uefi) and need to flash a good one on it. I really don't want to dual boot window just to do it so i research for a way to do it on linux. I found this post but the github repo isnt here anymore. I found a backup of it on the wayback machine. But i am not sure if it is safe or not. If it is safe why was the repo closed what happened to it?

As far as I know there are these;

• Camel case = coolFileName
• Snake case = cool_file_name
• Kebab case = cool-file-name
• Pascal case = CoolFileName
• Dot notation = cool.file.name
• Flat case = coolfilename
• Screaming case = COOLFILENAME

Personally I prefer the kebab/dot conventions simply because they allow for easy "navigation" with (ctrl+arrow keys) between each part. What are your preferences when it comes to this? Did I miss any schemes?

Adds xdg-toplevel-icon for changing icon in places like the titlebar without needing to create desktop entries.

Also adds ext-image-capture-source and ext-image-copy-capture which is used for capturing outputs/windows, used in wlroots and Cosmic.

The last update was over a year ago it seems. I remember everyone talking about the desktop environment like it was the next big thing. May she rest in peace.

As funny as ever?

Hopefully this means no more blurry Xwayland apps.

cross-posted from: https://lemmy.ndlug.org/post/1050940