783
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
this post was submitted on 30 Jul 2024
783 points (97.7% liked)
Technology
59436 readers
2009 users here now
This is a most excellent place for technology news and articles.
Our Rules
- Follow the lemmy.world rules.
- Only tech related content.
- Be excellent to each another!
- Mod approved content bots can post up to 10 articles per day.
- Threads asking for personal tech support may be deleted.
- Politics threads may be removed.
- No memes allowed as posts, OK to post as comments.
- Only approved bots from the list below, to ask if your bot can be added please contact us.
- Check for duplicates before posting, duplicates may be removed
Approved Bots
founded 1 year ago
MODERATORS
The comments read like a lot of people don't quite understand the issue.
The bonnet (hood if you insist) latch may not warn a driver if it isn't secured correctly. If it is secured correctly then it is fine. So it isn't going to suddenly open.
If the latch isn't shut correctly and then the sensor doesn't report this then the bonnet may open unexpectedly.
If they can use a software update to correct the reporting then that's it fixed.
There's no issue with the actual latching mechanism. It's just the sensor for reporting the latching state.
It may be that it currently works on a two value system. i.e a value for correctly latched and a value for not latched. If that's the case and isn't just not providing the second valve correctly then a simple software change to only use the latched value would fix this. As any other value or the absence of a value will report it at unlatched.
It's a soft close latch, the frunk pulls the lid into the latching mechanism. The mechanism isn't doing it's job and needs to be replaced either with a properly adjusted soft close mechanism that grabs the lid, or with a non soft close standard latch that is very obvious to the user when it has not been properly closed.
Nope it's the latch switch. So something that is switched when the latch is closed. Not the latch itself.
It's a bit ambiguous, but I read it as saying it isn't the mechanism that's at fault, it's user error that's not currently being properly detected.
I don't think it's 'user error' exactly. Maybe when this has occurred, something in the frunk has obstructed the closing of the hood so it almost latched, but the deformed switch is detecting it as closed. I think they might be adjusting the switch sensitivity in software (maybe it uses a Hall effect sensor and a magnet?) so that this almost-closed condition will be reported as just being open.
..."Although the problem is with the hood latch" <--- literally from the article. Care to re-read?
You skipped over the part where a) the latch is deforming, and as a result of that deformation b) the sensor can't detect that it's not closed, and so c) Tesla is pushing an update that lets people know their deformed latch isn't closed properly.
But yes, we all misread the article. Not you. Definitely not you.
And what is the next word after the bit you have quoted?
Is it by any chance switch.
The full quote is deformation of the hood latch switch. Not the hood latch.
Thanks for further confirming my point that you're not reading it correctly.
No, it's quite literally not. Click the article, read the article all the way. Including the last paragraph. Where my quote is from.
Then read the recall. Then lookup the part. See what it is? Oh, it's the entire latch assembly. Good job! Proud of you sweetie. 😘 Keep licking those musky boots!
Did you read the recall? Again it says hood latch switch deformation.
That may be part of the hood latch assembly but again at no point does it say that the latch not latching is the issue. Only the reporting of the latching state.
You're really rather pathetic and I'm certainly no fan of Tesla or Musk. A brief check of my previous posts would confirm this.
As you're obviously not very good at reading or understanding things then that fact probably did slip by you. You seem to be only capable of latching (you might not see what I did there being a bit dense) onto certain words without understanding the full issue.
You missed the part where the latch is deforming, causing it to not close or alert the driver. The software fix is yet another attempt to dodge the fact that they do not have enough repair capacity or financial reserves for a major fleet recall.
Read it again. It's deformation of the hood latch switch. Not the hood latch.
Thanks for further confirming my point that you're not reading it correctly
Too bad the software isn't open source.
While that may "solve" the issue, it's still due to a faulty physical component. A software update is just a bandaid over the real problem.