A converter that allows attachment of a 100mm hose to standard in wall extractor fan (160mmx1600m). I use this to allow me to extract heat/fumes from my 3d printer enclosure using my workshops built in extractor fan.

This is a Holder for a Fairphone 4. I designed it to replace a holder I already had in my car that was too small for the fairphone, so there were parts, that I already had installed and reused. (Ball-joint and gooseneck) I included a stub balljoint with a throat od of 5mm that has a 2.5mm bore so you can screw a m3 bolt in there. The fit of the holder works great with my own bumper case, but I had a bigger one on there before and that still fit. The female part of the balljoint is fixed to the holder with 4 countersunk 10mm M3 screws. printing: If you want to use it in a car, use heat resistant filament with good layer adhesion. PETG might work, I used PCTG and it works great. Parts with threads @0.1 layer height, the rest@ 0.2mm. Annealed PLA might also work. Give it plenty of printing temp for better layer adhesion, especially the balljoint parts need it.

English The 3D4U Borehole Cleaning Aid ensures that your hands are free when working with a drill. Mounted on the hand-piece, this accessory automatically secures itself to the wall. For this purpose, the base plate was optimized for the airflow by computer simulation. The nine openings draw in the dust that accumulates around the borehole when drilling particularly effectively. The result: less stress during drilling, a clean floor and more safety when working on ladders. Tip: Sensitive walls can be taped in advance to avoid residue on the wall after drilling. German Der 3D4U Bohrlochabsauger sorgt für freie Hände beim Arbeiten mit der Bohrmaschine. Am Griffrohr montiert, saugt sich dieses Zubehör selbstständig an der Wand fest. Dazu wurde die Bodenplatte per Computersimulation strömungsoptimiert. Die neun Öffnungen saugen den anfallenden Bohrstaub um das Bohrloch herum besonders effektiv ab. Das Ergebnis: Weniger Stress beim Bohren, ein sauberer Fußboden und mehr Sicherheit bei der Arbeit auf Leitern. Tipp: Empfindliche Wände können vorab mit Klebeband abgeklebt werden, um Rückstände an der Wand nach dem Bohren zu vermeiden.

I added a hole to be able to release the clip after it clicked. No other changes to it. The original part: https://www.thingiverse.com/thing:2594163 The idea for the hole: https://www.thingiverse.com/thing:5364218

Parts designed to use multiple lengths of 1/2 inch Schedule 40 PVC pipe for greater strength and rigidity. . Also may be used with wooden dowels (of appropriate size) if the use of PVC offends your sensibilities.

Cable organizer.

All the things you need when leaving your home ready to go! A Shelf for your wallet and magnetic holders for two sets of keys. The design has compartments for magnets with a diameter of 10mm max. Blender file included.

I wanted to mount my Dremel to a bench, but the original model by Faklam had a ring the Dremel didn't fit though (I later realised that the top can be screwed off). So I cleaned up the model, made the ring bigger, and ended up almost remodelling the whole thing. Unlike the original, the head of the tool is pressed against the small ring rather than going through it, which should be stable enough for most applications. For printing, I used supports for only the most horizontal parts of the rings. In this case I used a 0.6 mm nozzle and a layer height of 0.36 mm, as this model doesn't require much detail :)

This design has been updated with AUX port. You can find this new design at: https://www.thingiverse.com/thing:5767765 My PC has USB 3.0 ports only from its back (yes, it is already getting mature). I wanted to bring some of these to my desk to avoid having to 'deep dive' every time I need to connect something reasonably fast way. I have bought this cable and designed under-desk holder for it: PremiumCord USB 3.0 Super-speed 5Gbps A-Ahttps://www.alza.cz/premiumcord-prodluzovaci-kabel-usb-3-0-super-speed-5gbps-a-a-mf-9pin-2m-bila-d6696333.htm I think the design might work for some other brands as well as it is quite common shape for this type of wire. You should use 2 pcs. of 3mm screws to fix it to the table - whichever length works for you, I have used 16mm. Easy to print, but you need to position the objects properly to the printing bed. Consult the picture for object orientation on the bed. I have used 0.6mm nozzle, orange PETG filament, 55% infill and supports. Happy printing :o]

100mm flexi hose holder

Deux appareils pour faciliter l'ouverture des bouteilles avec bouchons vissés. pour les fixer sur votre réfrigérateur vous pouvez coller 4 aimants diamètre 6X2mm. Voici un lien pour les aimants. Vous pouvez imprimer séparément les deux fichiers. https://www.amazon.fr/gp/product/B07RT9MY52/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 Two devices to facilitate the opening of bottles with screw caps. to fix them on your refrigerator you can stick 4 magnets diameter 6X2mm. Here is a link for the magnets. You can print both files separately. https://www.amazon.fr/gp/product/B07RT9MY52/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

Small latch for cabinet, little door, to attach something to other thing. Works well also as printer test. Gap between parts is 0.2 mm. Can be printed fully working on place without supports as shown on video. If you have problems with movement most likely problem is stringing. https://youtu.be/MCwRCMNyMc4